Civil Engineering - Water Supply Engineering MCQs Part 8

1. Capacity of soil to absorb moisture, is generally known as

A.
permeability
B.
porosity
C.
infiltration capacity
D.
perviousness.

 Answer Option C

2. At break point of chlorination,

A.
chlorine is used to oxidise
B.
residual chloride is zero
C.
residual chloride is maximum
D.
residual chlorine reappears.

 Answer Option D

3. The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the riveted joints of the pipe as 0.6 and minimum cover 3 mm for corrosion, the thickness of the pipe materials, is

A.
10 mm
B.
15 mm
C.
20 mm
D.
25 mm
E.
30 mm.

 Answer Option C

4. The factor for the selection of pumping station site, is

A.
distance of the source of contamination or pollution
B.
height above the H.F.L. of the river
C.
future expansion
D.
proximity of the site from the railway station
E.
all the above.

 Answer Option E

5. Low turbidity of water is detected by

A.
Turbidity tube
B.
Jackson turbidity meter
C.
Baylis turbidimeter
D.
Hellipe turbidimeter
E.
None of these.

 Answer Option C

6. Pick up the incorrect statement from the following :

A. The pH value of water indicates the logarithm of reciprocal of hydrogen ion concentration in water
B. Higher value of pH means lower hydrogen ion concentration
C. Lower value of pH means higher hydrogen ion contraction
D. Lower value of pH gives alkaline solution
E. None of these.

 Answer Option D

7. Pick up the correct statement from the following :

A. The volume of underground water extracted by gravity drainage from a saturated soil, is known as yield
B. The ratio of volume drained to the total volume of material drained, is known as specific yield
C. The volume of water retained by the soil against the pull of gravity, is called specific retention or field capacity
D. The sum of specific yield and specific retention, is equal to porosity
E. All the above.

 Answer Option E

8. Perched acquifers generally occur

A. below water table
B. above water table
C. in acquicludes
D. in artesian acquifers
E. none of these.

 Answer Option B

9. Silt storage is the same as

A. dead storage
B. live storage
C. effective storage
D. none of these.

 Answer Option A

10. For complete stabilisation of organic matter in polluted water, it takes

A. 5 days
B. 10 days
C. 20 days
D. 30 days
E. 40 days.

 Answer Option D

11. A pressure conduit carrying water beneath a stream or a canal, is known as

A. sag
B. depressed pipe
C. inverted syphon
D. all the above.

 Answer Option D

12. Suction lift of a pump depends upon

A. atmospheric pressure
B. water temperature
C. velocity of water in suction pipe
D. frictional losses
E. all the above.

 Answer Option E

13. For 3.25 x 10-2 cumecs discharging from a well, a pump is installed to lift water against a total head of 30 m. The minimum required horse power, is

A. 10 H.P.
B. 15 H.P.
C. 18 H.P.
D. 20 H.P.
E. 25 H.P.

 Answer Option D

6. Pick up the incorrect statement from the following :

A. The pH value of water indicates the logarithm of reciprocal of hydrogen ion concentration in water
B. Higher value of pH means lower hydrogen ion concentration
C. Lower value of pH means higher hydrogen ion contraction
D. Lower value of pH gives alkaline solution
E. None of these.

 Answer Option D

7. Pick up the correct statement from the following :

A. The volume of underground water extracted by gravity drainage from a saturated soil, is known as yield
B. The ratio of volume drained to the total volume of material drained, is known as specific yield
C. The volume of water retained by the soil against the pull of gravity, is called specific retention or field capacity
D. The sum of specific yield and specific retention, is equal to porosity
E. All the above.

 Answer Option E

8. Perched acquifers generally occur

A. below water table
B. above water table
C. in acquicludes
D. in artesian acquifers
E. none of these.

 Answer Option B

9. Silt storage is the same as

A. dead storage
B. live storage
C. effective storage
D. none of these.

 Answer Option A

10. For complete stabilisation of organic matter in polluted water, it takes

A. 5 days
B. 10 days
C. 20 days
D. 30 days
E. 40 days.

 Answer Option D

Comments

Post a Comment

Most Popular

Remove Unicode Zero Width Space PHP

✔ Recommended Answer This: $newBody = str_replace("​", "", $newBody); presumes the text is HTML entity encoded. This: $newBody = str_replace("\xE2\x80\x8C", "", $newBody); should work if the offending characters are not encoded, but matches the wrong character (0xe2808c). To match the same character as #8203; you need 0xe2808b: $newBody = str_replace("\xE2\x80\x8B", "", $newBody); Source: stackoverflow.com Answered By: Jef Method #2 To remove Unicode zero width space (ZWSP) from a string in PHP, you can use the str_replace() function to replace the ZWSP character with an empty string. Here's an example: php $str = "Hello​ World" ; // Contains ZWSP after "Hello" // Replace ZWSP with an empty string $str = str_replace ( "\u{200B}" , "" , $str ); echo $str ; // Outputs "Hello World" without ZWSP In this example, the str_replace() functi
Read more

PhpStorm, return value is expected to be 'A', 'object' returned

Image
✔ Recommended Answer Has to be because object can be ANY class instance, even B etc. You can annotate the create() method with generics PHPDoc to tell that the return type will be the same as the input parameter class string. It gives more context info to the IDE. /** * @template T * * @param string $class * @return T */ private function create(string $class) : object { return new $class(); } P.S. Instead of create('B'); better use create(B::class) . This way the IDE can track the usages of that class for refactoring/search purposes etc. Source: stackoverflow.com Answered By: LazyOne Method #2 This error message suggests that your code is expecting a value of type 'A' to be returned, but instead, the code is returning an object. This error can occur in PhpStorm, or any other PHP development environment. To resolve this error, you should check the function or method that is returning the object and ensure that it is returning
Read more

Laravel file upload returns forbidden 403, file permission is 700 not 755

✔ Recommended Answer The issue you are facing could be due to incorrect file permissions for the storage folder. Here are some steps to fix the problem: SSH into your cPanel server. Change the permission of the storage folder to 755: chmod -R 755 storage/ This command will change the permission of the storage folder and all its contents to 755, which should give the web server permission to read and write to the folder. Check the ownership of the storage folder. Ensure that the owner of the folder is the same as the user running the web server (typically www-data on Apache): ls -l This command will list the files and folders in the current directory along with their ownership and permission details. Make sure that the owner of the storage folder is the same as the user running the web server. If the ownership is incorrect, you can change it using the following command: chown -R www-data:www-data storage/ This command will change the ownership of the storage folder and all its conten
Read more